The forces in a bank
Now we're ready to look at an actual airplane and its forces, from the front. Here we ignore thrust and drag, which point into and away from the screen. What we do see are lift, doing simply what its name says, pointing straight up at the sky, and weight, pointing straight down. In straight-and-level flight they directly oppose each other with the same strength. If the weight is, say, 2000 pounds, then the lift is also 2000 pounds, so the flight path does not curve up or down, but continues to go in a straight line.In the second picture, we have a moderate amount of bank angle. Weight, of course, continues to pull straight down toward the Earth. Lift, however, banks with the airplane, and continues to point out of the "roof" of the airplane perpendicular to the wings. This is an important maxim that is a fundamental cornerstone of most of flight dynamics, so I will hit upon it here as a key point: Lift always points perpendicular to the airplane.
You may note that as we continue to bank steeper and steeper, and thus aim the lift vector steeper and steeper, at a certain point lift no longer does what its name implies, since we can aim it at the ground! At this point, it's important to note that "lift" is just a name (that only describes what it normally does in straight and level flight), and when we have it aimed at the ground you'll only get confused by trying to figure how it lifts the airplane; it doesn't. We might as well name it "wing force," since it plainly describes that it's just the force created by the wing. But the name "lift" has stuck, and we have to be careful not to take it to mean any more than it does.
In this picture, so-called "lift" is aimed mostly down, and acts in the same direction as weight; All the forces push it down and nothing opposes them, so you can be sure this airplane will be going down quickly. (How, then, do aerobatic airplanes perform sustained inverted flight? That's a topic for a future article, but in short, we manipulate lift so that it comes out the belly of the airplane rather than the roof. And yes "roof" is a silly word but I use it to avoid any confusion with where up and down are, while the airplane is itself upside down.)
Why does this matter?
Why we bank
Go back to the second picture, with the moderate bank angle:Recall the question that began my last post: "Why does the airplane turn?" This is why. Very simply put, we have tilted the lift force to one direction, and like Apollo LES rocket it will now pull the airplane in that direction. A force exists to the right (from the pilot's point of view), where none did before; therefore the plane will move to the right, where it wasn't before. Of course, it's only a partial tilt, so the lift force pulls double-duty: it still acts to counter weight (though not as effectively as before) while also turning us. The further over we tilt it, the less it will lift us and the more it will turn us. If we tilt it fully 90 degrees, it will not counter weight at all, but it would turn us most effectively. For a basic description, it really is that simple: You aim your lift vector where you want the airplane to go, so it goes that way.
I've seen students' eyes glaze over when we start breaking down the lift vector into horizontal and vertical components and they start getting flashbacks from high school trigonometry class. I thought flying was supposed to be fun! Well sometimes it takes a little brainwork (and, not to worry, I'll cover this in a future post) but sometimes that brainwork can make you miss the forest for the trees. Anything about vector components and horizontal-this and vertical-that is detailed techniques for calculating how much lift it takes to do one job or the other. For now forget about it and please appreciate the basic notion that you move the airplane around with the lift vector.
A little bank, a little tilt, a little sideways pull, a gentle turn.
A steep bank, a big tilt, a strong sideways pull, a sharp turn.
The venerated ailerons, for their part, are not very important. They are just one of many methods of establishing the bank (and therefore the lift vector tilt) but the bank itself is the important part, for without it the lift vector won't point sideways, and so we can't have a turn. How about the many airplanes without ailerons? The Wright Flyer, for one, didn't have ailerons but used wing-warping instead. You might object that it's an unfair example since wing-warping still does the same thing as an aileron deflection: moving the trailing edge up or down, just smoothly without a hinge. Fine. How about the B-52? No ailerons, and no wing warping. It uses differential spoilers to meet the objective of establishing a bank and tilting the lift vector. Or weight-shift ultralights: You move the center of gravity to the side, and that makes it bank and tilts the lift vector. In summary, what matters is not how we bank, but why we bank.
Airplane control
Not just turning, but all maneuvering boils back down to the manipulation of the lift vector. Fundamentally, there are 2 things we can do with it: change its direction, as we saw, by banking the airplane with (or without, for that matter) ailerons; and its magnitude, by pitching with the elevator.In a normal turn, we bank it sideways a little, so it starts pulling us to the side, and we pull back the stick slightly to increase its magnitude to make up for its reduced ability to lift the airplane. Or, from level flight, we can simply pull back on the stick a lot, to increase lift magnitude a lot, so as to curve our flight path upwards into a loop. I can go on with more examples, but the bottom line is that all of flight, from normal maneuvers, to emergency maneuvers, to aerobatics, to aerial combat, can be reduced to working the lift vector in direction and magnitude (or, strength). So, always be asking yourself about your lift vector: 1) where am I pointing it? and 2) how strong am I making it?
When thinking about the mechanics of these interactions, all of this probably isn't Earth-shattering news. My point in laying out these results in so many ways (and repetitions) is to further a meaningful understanding of flight (especially maneuvering flight) by more directly connecting your control inputs to these ultimate results, rather than the basic airplane motions.
Consider a car analogy: If you teach someone from an isolated tribe how to drive a car, while explaining the purpose of the steering wheel, you wouldn't say that it's to control the lateral displacement of the steering rack. While accurate, that doesn't explain much. "To turn" does. Likewise, the purpose of the two possible yoke/stick displacements, is much more than simply to control pitch and roll. Why do we pitch and roll? Like the real purpose of the steering wheel is to turn, the real purpose of moving the yoke is to manipulate the lift vector in the ways discussed earlier. And to help soak that in to your understanding of maneuvering flight, in your mind re-label the motions of the yoke from their direct results in the conventional picture to the left, to their ultimate results in the picture to the right.









